![]() I created a new layer with a u-boot-imx_2017.03.bbappend to extend u-boot-imx_2017.03.bb (the recipe for u-boot-imx). config file, and copied it to my layer and renamed to "defconfig". I followed this guide for kernel configuration with the Yocto project. There are many xxx_defconfig files and I don't know which it is using. The City of Fawn Creek is located in the State of Kansas. ![]() find the build directory and run make menuconfig), but when I run bitbake to rebuild the image, it overwrites the. change the auto boot delay to 1 second as an example. config used to build u-boot-imx (u-boot for the iMX dev board) – e.g. INHERIT + 'trustfence' Image signing is enabled by default. Configure secure boot To build signed and encrypted artifacts, modify your conf/nf file to include the following: conf/nf Required to include trustfence support. For instance, in your local.Building linux for an iMX6 dev board using the Yocto Project, and I want to change the. To add secure boot support to your Digi Embedded Yocto project: 1. We will also explain how the Linux side can cooperate with the U-Boot. Project you need to enable the mender-uboot feature using Current documentation maintainer for the Yocto Project. To utilize Mender's integration with U-Boot, when building with the Yocto Many machine configurations will probably have this in their setup already. Implementation using PREFERRED_PROVIDER, like this: PREFERRED_PROVIDER_u-boot = "u-boot-my-fork" In the machine section of the board, you need to select the actual u-boot Mender has a dependency on u-boot, but the project's U-Boot likely hasĪnother name, therefore it is important to mark the project's fork as aĬomponent that provides u-boot. Recipe for the U-Boot fork: require recipes-bsp/u-boot/u-boot-mender.inc The recipe needs to include u-boot-mender.inc, in order to incorporate the Typically this happens if one of the layers the project depends on has If the project is using a fork of U-Boot, some additional steps are Let's say I just want to modify u-boot, how should I proceed I am following the Tasks which are published on this forum. If any variables appear, and any one of them has a value other than u-boot orĮmpty, then the build is using a U-Boot fork. 06-19-2013 07:25 AM 35,547 Views AlbertT Contributor V Hello, I am starting to use Yocto but I have a lots of difficulties to understand how it works. You can check if the board is using a u-bootįork with the following command (executed in the Yocto build directory): bitbake -e core-image-minimal | egrep '^PREFERRED_PROVIDER_(virtual/bootloader|u-boot)=' config used to build u-boot-imx (u-boot for the iMX dev board) - e.g. Using the u-boot recipe as the bootloader provider, then you can skip to the Building linux for an iMX6 dev board using the Yocto Project, and I want to change the. If the project is using a board supported by upstream U-Boot, and the build is See the documentation on features for more information. yocto u-boot nvidia-jetson nvidia-jetson-nano Share Follow edited at 9:50 asked at 10:41 Varyag 676 10 28 Did you look at this presentation Nayfe at 11:29 I did not Giving it a go and returns to either edit question or give an answer, ty. MENDER_FEATURES_DISABLE:append = " mender-grub mender-image-uefi" Create a u-boot-variscite.bbappend file: gedit u-boot-variscite.bbappend and append the following line to it: SRCURI + 'file://mym圆varsomchanges.diff' Also update the u-boot-fw-utils recipe: cp u-boot-variscite.bbappend u-boot-fw-utils. i have my file: u-boot-tftp.pacth under the directory: /file/u-boot-tftp. The i.MX8MQ secure boot document covers those needed topics. how to apply patch uboot: Yocto project Ask Question Asked 4 years, 4 months ago Modified 4 years, 4 months ago Viewed 2k times 0 i'm trying to apply a patch during the creation of my image with bitbake commande. This document omits Code Signing Tool and HAB Key Generation information needed for a successful secure boot. ![]() For instance, in your nf: MENDER_FEATURES_ENABLE:append = " mender-uboot mender-image-sd" It is a subset of i.MX8MQ secure boot document as most of the information is similar. If U-Boot integration is not already enabled, you can enable it by adding the snippet below to your build configuration. Platform supports U-Boot, and whether it is enabled by default. Please consult the bootloader support section to find out if your How to make an apply-device-config script.Production installation with Kubernetes. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |